Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
- 10. Suspension bracket and steering
10.1. Specifications
10.2. Rack of a suspension bracket (lobby)
10.3. Suspension bracket rack
10.4. Stabilizer of cross-section stability (a forward suspension bracket) and plug
10.5. Suspension bracket lever
10.6. Spherical hinges
10.7. Rotary fist and nave
10.8. Nave and nave bearing (a forward wheel)
10.9. Stabilizer of cross-section stability (a back suspension bracket) and plug
10.10. Rack of a suspension bracket (back)
10.11. Longitudinal draft
10.12. Cross-section drafts of a suspension bracket
10.13. Nave and bearing (a back wheel)
10.14. Arm of a nave of a back wheel
10.15. Steering
10.16. Steering wheel
10.17. Tips of steering drafts
10.18. Steering transfer
10.19. Pump of system of strengthening of a steering
10.20. System of strengthening of a steering
10.21. Wheels and tires
10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment
|
Prevention
On these models the safety airbag is established. The airbag of safety can reveal (will be filled with air) at any time when it is connected to the accumulator. In order that it casually did not reveal (and did not put a trauma), turn a key in the ignition lock in the situation LOCK and disconnect a wire of the negative plug of the accumulator before the work beginning with a safety cushion. After a detachment of the accumulator wait for at least two minutes before the work beginning, (the module of a safety cushion has the condenser block which should be discharged completely). For more information look chapter describing electric equipment of the car.
Removal
| PERFORMANCE ORDER |
1. Turn a key in the ignition lock in the situation OFF, then disconnect a wire of the negative plug of the accumulator. If on the car the safety airbag is established, wait for at least two minutes before further work.
Prevention
Put a safety airbag the face up.
|
|
2. For receiving access to fixing screws of an airbag of safety remove casing halves on each side a steering column.
|
|
3. Turn a steering wheel so that forward wheels looked precisely directly, then remove small casings (if are established) on each side a steering wheel and turn off T30 screws with the face heads, safety fixing an airbag to a steering wheel. |
|
4. Turn off screws so that the rim on a circle of the screw rested against a nest (1 – the face screw, 2 – a screw nest). Remember that on some models, two screws, and on the right side only one are on the left side located. |
|
5. Remove a safety airbag from a steering wheel. |
|
6. Lift a fixing uvula of the socket of connection of a pillow and disconnect it. |
Prevention
Put a safety airbag the face up.
|
| 7. Disconnect the socket of connection of system cruise control (if it is established). |
|
8. Turn off a fixing nut of a steering wheel (it is specified by shooters) and note the provision of installation of a steering wheel in relation to a shaft of a steering column (if the mark is not made yet or if they do not coincide) for simplification of installation of a steering wheel. |
|
9. By means of a stripper remove a steering wheel from a shaft of a steering column. If the steering wheel does not act in film from a shaft of a steering column, use the demountable device. |
|
Installation
| PERFORMANCE ORDER |
|
1. Check, that forward wheels looked precisely directly. Turn the rope twirled by a spiral counter-clockwise a hand while it is not becomes strong to resist. Turn a rope clockwise on three turns and combine two red indexes (the rope will be scrolled approximately on three turns to the right or to the left from the center).
|
| 2. For installation of a steering wheel, combine a mark in a steering wheel with a mark on a shaft of a steering column and put on a steering wheel a shaft of a steering column. Establish a fixing nut and tighten it till the demanded moment of an inhaling (see subsection 10.1). |
| 3. Connect the socket of connection of wires of system cruise control. |
| 4. Connect the socket of connection of wires of an airbag of safety and lower a fixing uvula. |
|
5. Check, that the socket of connection of an airbag of safety was located correctly, and wires disturbed nothing (1 – connection, 2 – wires for a safety cushion). Then, establish an airbag of safety and tighten fixing screws with heads under face a key till the demanded moment of an inhaling (see subsection 10.1). |
| 6. Connect a wire of the negative plug of the accumulator. |
|
|
|